Author Topic: Help turn light sostitusion  (Read 1000 times)

0 Members and 1 Guest are viewing this topic.

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Help turn light sostitusion
« on: February 19, 2018, 08:38:15 PM »
Hi everybody,
I would like to replace the old not original turn light (previous owner) with the original ones.
Previous have 2 wire, the genuine only 1.
If I connect only one wire (green and not black (mass)) it's ok? it's working?
I'm not expert
thank you
« Last Edit: February 19, 2018, 08:41:20 PM by Rufus »

Offline dailydose1

  • Full Member
  • ***
  • Posts: 229
  • Karma: 0
    • Lebanon
Re: Help turn light sostitusion
« Reply #1 on: February 20, 2018, 01:11:55 AM »
i believe my cb350 has the turn signal grounded in the turn signal with only one wire so it should be fine. is it working?

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitusion
« Reply #2 on: February 20, 2018, 07:19:00 PM »
Thank you, I 'll try as soon as possible...work in progress  ;)

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitution
« Reply #3 on: April 01, 2018, 08:53:05 PM »
Yesterday I tried but not working, the old turn light (not original) with two wires was placed green wire in X and black wire in N as in photo...and so work, but when I replace with new original light I place the only one wire in X but not work....help me please
« Last Edit: April 01, 2018, 08:55:32 PM by Rufus »

Offline guylr

  • Administrator
  • Hero Member
  • *****
  • Posts: 1139
  • Karma: 19
    • ATL in the USA
Re: Help turn light sostitusion
« Reply #4 on: April 01, 2018, 09:41:23 PM »
You are missing the ground wire. The single wire signals used a ground wire that attached under the nut you used to mount the signal. Run a wire from that nut to the black wire harness connection.

Guy
Now Retired Yamaha guy. Cut me and I bleed "Cinquasia Red"

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitution
« Reply #5 on: April 01, 2018, 10:35:19 PM »
Ok thanks Tomorrow I will try 

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitusion
« Reply #6 on: April 02, 2018, 09:54:07 PM »
I tried and turn light now are OKKKK thanks you very much......only now I realized I had a black wire not connected,  in fact now it seems to me that the light of the speedometer does not turn on..but not have pin free... :o   any idea?

Offline guylr

  • Administrator
  • Hero Member
  • *****
  • Posts: 1139
  • Karma: 19
    • ATL in the USA
Re: Help turn light sostitusion
« Reply #7 on: April 02, 2018, 11:55:41 PM »
Blue wire. Do you have a wiring diagram?

Guy
Now Retired Yamaha guy. Cut me and I bleed "Cinquasia Red"

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitusion
« Reply #8 on: April 03, 2018, 09:19:19 AM »
If you see the photo in previous post the wire is in letter F it seems black, when I  entered the ground wire I realized that it should not be there, so I disconnected because there it was inserted ground wire, but now I do not know where to insert.
Unfortunately not wiring diagram that I probably could not read.
Rob

Offline Rufus

  • Jr. Member
  • **
  • Posts: 27
  • Karma: -1
    • italy
Re: Help turn light sostitution
« Reply #9 on: April 03, 2018, 03:57:01 PM »
I resolved, I had not seen another free PIN to the other side F letter...
it is a bit complicated...I know....but now it's all Ok.
Thank you Guy
Rob