How Much To Get The Drive Belt Replaced On My 1999 Harley Davidson?
- 1 How often should Harley drive belt be changed?
- 2 Is replacing a drive belt expensive?
- 3 How much does a belt repair cost?
- 4 What causes Harley drive belt to break?
- 5 How long does a Harley-Davidson drive belt last?
- 6 How much does it cost to replace a belt on a Harley?
- 7 How long does it take to replace a drive belt?
- 8 What are the symptoms of a bad drive belt?
- 9 Can I replace a serpentine belt myself?
- 10 Is a timing belt the same as a serpentine belt?
- 11 What would be a reasonable cost for a serpentine belt and replacement?
- 12 How do you know when to replace a belt tensioner?
- 13 How long does a drive belt last on a motorcycle?
How often should Harley drive belt be changed?
The maintenance schedule for all Harley motorcycle models calls for a drive belt inspection and tension check after the first 1,000 miles and every 5,000 miles thereafter, the same interval as an oil-and-filter change.
Is replacing a drive belt expensive?
The driving belt replacement cost is usually just between $100 and $200 in most cases, with the belt and part itself costing between $28 and $80, while the labor costs will be between $75 and $120 total.
How much does a belt repair cost?
A typical serpentine belt start at around $25 and goes up to $75 at most. If you know some car repair basics, you could change the belt yourself, and it may save you paying labor charges somewhere between $75 and $120. All together, you’re looking at around $100 to $195 to replace your serpentine belt.
What causes Harley drive belt to break?
when a small dry rotted or crack or slice has been improvised into the material, it then is put under stress it will rip at that asperity or joint crack and tear apart. I too have seen “new belts” fail.
How long does a Harley-Davidson drive belt last?
Because a drive belt can last up to 100,000 miles before needing replacement, riders may lose track of this important part of motorcycle maintenance.
How much does it cost to replace a belt on a Harley?
Harley drive belts are very strong and durable and only need replacement after thousands of miles of riding. Unless you have a warranty, a replacement will cost a few hundred dollars at your Harley dealer. Do it yourself in about 30 minutes, for less than $50.
How long does it take to replace a drive belt?
Changing the belt should only take about 15 minutes. Make sure the car is switched off and cooled down before touching any part of the engine. Read your belt routing diagram. This may be under the hood or in your car’s manual.
What are the symptoms of a bad drive belt?
Symptoms of a Bad or Failing Timing Belt
- You Hear A Ticking Noise Coming From The Engine.
- Your Car’s Engine Won’t Turn Over.
- You Notice An Oil Leak Near The Motor.
- You Experience Exhaust Issues.
- Your Revs Start Acting Up.
Can I replace a serpentine belt myself?
You can replace a serpentine belt with ordinary hand tools. But we don’t recommend it. The spaces are often tight and the belt-driven devices difficult to reach. The belt placement tool allowed us to remove and properly place the new belt without reaching down into the pulley area.
Is a timing belt the same as a serpentine belt?
Timing Belt. Don’t get confused— a serpentine belt is not the same thing as a timing belt. The serpentine belt and timing belt have very different functions in your vehicle. The timing belt is located inside the engine and keeps the crankshaft and camshaft in sync.
What would be a reasonable cost for a serpentine belt and replacement?
It is very inexpensive to replace a serpentine belt whether it’s broken or loose. The replacement cost is only going to be between $100 and $200 in most cases. The belt itself will cost between $25 and $80 while the labor costs will probably be between $75 and $120.
How do you know when to replace a belt tensioner?
Appearance: Cycle the tensioner (mounted on the engine) through the entire range of motion (from stop to stop) by applying torque to the arm with a wrench. The tensioner arm should move smoothly and freely. Solution: If you notice a binding, sticking or grinding tensioner arm, the tensioner should be replaced.
How long does a drive belt last on a motorcycle?
A properly cared for drive belt can last a hundred thousand miles, and maintaining it just means checking its condition and tension about as often as you change the oil and filter.